Hello!

Did you know that logged in users can see a lot more content?

Tekla Tedds Engineering Library (July 2018)

Last updated July 23, 2018 by Tedds Development Team tekla-product-development-tedds-team-ug@trimble.com

Tekla Tedds Engineering Library (July 2018)

Contents

UK and Asia

RC beam analysis & design (EN1992)

Enhanced to simplify the user interface and to improve the calculation performance for an overall improved user experience.
Watch video

Product bulletin July 2018 (PBT-1807-1)

Steel beam analysis & design (BS5950) - Fixed a potentially un-conservative error affecting the calculation of the unrestrained buckling length where the restraints differ at each support. For more detailed information please refer to “Product bulletin July 2018 (PBT-1807-01)” in the Bulletins group of the Engineering Library Index.

Other updates

2D analysis

Improved output geometry table for models of a single design member to show all section properties when a custom steel section is used from a steel design calculation.
Enhanced to include a new "2D analysis creator" calculation which will create a default analysis model based on the specified model type, material and design code.
Added geometry for all Timber default models.
Updated default load combinations for all Steel and Concrete default models.
Enhanced to include _analysisUIShowMemberAngle setting which determines whether the geometry tab of the single member user interface shows an edit box for defining the angle of the design member.
Enhanced to include _analysisUIShowSectionEdit setting which determines whether the geometry tab of the single member user interface shows an "Edit…" option on the section drop list which allows the analysis and design properties of the section to be modified.

Composite beam design (BS5950)

Updated information in user interface to refer to Tekla Structural Designer.

Concrete industrial ground floor slab design (TR34)

Fixed an undefined variable error when the user defined fabric option is selected
Fixed the interface preview results for shear at 2d to include the ground reaction reduction.

Crane gantry girder design (BS5950)

Corrected weld table reference in the output.

RC beam analysis & design (EN1992)
RC 2D analysis & design (EN1992)
RC beam design (EN1992)

Enhanced to simplify the user interface and improve the overall user experience.
Optimized user interface to improve performance when updating design results.
Fixed overlapping section diagrams when designing wide beams.
Fixed an error when reselecting a T-section.
Fixed several minor undefined variable errors.
Fixed errors when updating previously calculated documents in design only calculation.

RC column design (EN1992)

Improved output sketch for rectangular sections so that text lines do not overlap when width of section is narrow relative to depth.

Steel member analysis & design (EN1993)
Steel 2D analysis & design (EN1993)
Steel member design (EN1993)

Corrected undefined variable errors associated with summary output tables.
Corrected error associated with custom sections.
Amended analysis output options.

USA

Steel 2D analysis & design (AISC360)
Steel member analysis & design (AISC360)
Steel member design (AISC360)

Enhanced in accordance with AISC360-16.

RC beam analysis & design (ACI318)

Enhanced to simplify the user interface and to improve the calculation performance for an overall improved user experience.

Other updates

2D analysis

Improved output geometry table for models of a single design member to show all section properties when a custom steel section is used from a steel design calculation.
Enhanced to include a new "2D analysis creator" calculation which will create a default analysis model based on the specified model type, material and design code.
Added geometry for all Timber default models.
Updated default load combinations for all Steel and Concrete default models.
Enhanced to include _analysisUIShowMemberAngle setting which determines whether the geometry tab of the single member user interface shows an edit box for defining the angle of the design member.
Enhanced to include _analysisUIShowSectionEdit setting which determines whether the geometry tab of the single member user interface shows an "Edit…" option on the section drop list which allows the analysis and design properties of the section to be modified.

RC 2D analysis & design (ACI318)
RC beam analysis & design (ACI318)
RC beam design (ACI318)

Enhanced to simplify the user interface and improve the overall user experience.
Optimized user interface to improve performance when updating design results.
Fixed overlapping section diagrams when designing wide beams.
Fixed several minor undefined variable errors.
Omitted the shear spacing check when no shear reinforcement is required.

Snow loading (ASCE7)

Corrected the drift width to use the calculated windward drift height.

Steel 2D analysis & design (AISC360)
Steel member analysis & design (AISC360)
Steel member design (AISC360)

Corrected undefined variable errors associated with summary output tables.
Corrected error associated with custom sections.
Amended analysis output options.
Revised equations for Lr and Fcr to exclude number of members. Number of members now accounted for correctly in final design capacity.
Revised weak axis shear to use kv equal to 1.2. No effect on standard sections.
Fixed defect not counting multiple members in yield moment in tension and compression flanges, Myt and Myc

Tilt-up wall panel design (ACI318)

Fixed 'undefined variable' error when calculating existing documents.

Australia

RC beam analysis & design (AS3600)

Enhanced to simplify the user interface and to improve the calculation performance for an overall improved user experience.

Other updates

2D analysis

Improved output geometry table for models of a single design member to show all section properties when a custom steel section is used from a steel design calculation.
Enhanced to include a new "2D analysis creator" calculation which will create a default analysis model based on the specified model type, material and design code.
Added geometry for all Timber default models.
Updated default load combinations for all Steel and Concrete default models.
Enhanced to include _analysisUIShowMemberAngle setting which determines whether the geometry tab of the single member user interface shows an edit box for defining the angle of the design member.
Enhanced to include _analysisUIShowSectionEdit setting which determines whether the geometry tab of the single member user interface shows an "Edit…" option on the section drop list which allows the analysis and design properties of the section to be modified.

RC 2D analysis & design (AS3600)
RC beam analysis & design (AS3600)
RC beam design (AS3600)

Enhanced to simplify the user interface and improve the overall user experience.
Optimized user interface to improve performance when updating design results.
Fixed overlapping section diagrams when designing wide beams.

Steel 2D analysis & design (AS4100)
Steel member analysis & design (AS4100)
Steel member design (AS4100)

Corrected undefined variable errors associated with summary output tables.
Corrected error associated with custom sections.
Amended analysis output options.

Canada

Updates

2D analysis

Improved output geometry table for models of a single design member to show all section properties when a custom steel section is used from a steel design calculation.
Enhanced to include a new "2D analysis creator" calculation which will create a default analysis model based on the specified model type, material and design code.
Added geometry for all Timber default models.
Updated default load combinations for all Steel and Concrete default models.
Enhanced to include _analysisUIShowMemberAngle setting which determines whether the geometry tab of the single member user interface shows an edit box for defining the angle of the design member.
Enhanced to include _analysisUIShowSectionEdit setting which determines whether the geometry tab of the single member user interface shows an "Edit…" option on the section drop list which allows the analysis and design properties of the section to be modified.

Europe

RC beam analysis & design (EN1992)

Enhanced to simplify the user interface and to improve the calculation performance for an overall improved user experience.
Watch video

Other updates

2D analysis

Improved output geometry table for models of a single design member to show all section properties when a custom steel section is used from a steel design calculation.
Enhanced to include a new "2D analysis creator" calculation which will create a default analysis model based on the specified model type, material and design code.
Added geometry for all Timber default models.
Updated default load combinations for all Steel and Concrete default models.
Enhanced to include _analysisUIShowMemberAngle setting which determines whether the geometry tab of the single member user interface shows an edit box for defining the angle of the design member.
Enhanced to include _analysisUIShowSectionEdit setting which determines whether the geometry tab of the single member user interface shows an "Edit…" option on the section drop list which allows the analysis and design properties of the section to be modified.

RC beam analysis & design (EN1992)
RC 2D analysis & design (EN1992)
RC beam design (EN1992)

Enhanced to simplify the user interface and improve the overall user experience.
Optimized user interface to improve performance when updating design results.
Fixed overlapping section diagrams when designing wide beams.
Fixed an error when reselecting a T-section.
Fixed several minor undefined variable errors.
Fixed errors when updating previously calculated documents in design only calculation.

RC column design (EN1992)

Improved output sketch for rectangular sections so that text lines do not overlap when width of section is narrow relative to depth.

Steel member analysis & design (EN1993)
Steel 2D analysis & design (EN1993)
Steel member design (EN1993)

Corrected undefined variable errors associated with summary output tables.
Corrected error associated with custom sections.
Amended analysis output options.

Content rating: 
No votes yet