Hello!

Did you know that logged in users can see a lot more content?

Tekla Tedds Engineering Library (July 2019)

Last updated July 30, 2019 by Tedds Development Team tekla-product-development-tedds-team-ug@trimble.com

Tekla Tedds Engineering Library (July 2019)

Important

Service Pack 2 is required to use the Tedds Engineering Library (July 2019) or later.

Contents

UK and Asia

Updates

Column base plate design (EN1993)

[TEDDS-3210]1 Added to output derivation of Ft,Rd

RC beam analysis & design (EN1992)
RC beam design (EN1992)

Refactoring code for integration with other calculations.
[TEDDS-1017]1 - fixed the use of an incorrect lever arm when previous load has been removed in the design only calculation.
[TEDDS-1648]1 - Enhanced the calculation to include the option to select a user defined concrete strut angle in the shear checks.
[TEDDS-2514]1 - Fixed an error where preview results were sometimes incorrect.
[TEDDS-3034]1 - Fixed an error where the flanged details were not taken from the geometry section.
[TEDDS-3163/3164]1 - Fixed an error where spacing checks were included when user defined reinforcement areas were selected.
[TEDDS-3522]1 - Fixed an error in the preview results with certain end cantilever configurations.

RC pile cap design (EN1992/EN1997)

[TEDDS-3632]1 Fixed undefined variable error 'x_{p1}' when re-calculating a document where the pile locations have been manually modified.
[TEDDS-3637]1 Corrected non standard user interface title.

RC stair design (EN1992)

[TEDDS-3636]1 Fixed version number not been displayed in the user interface title.

Steel member fire resistance design (EN1993)

[TEDDS-3635]1 Fixed calculation version not being displayed in the user interface title.

Timber frame racking panel design (EN1995)

[TEDDS-3638]1 - Amended user interface to ensure calculation version is shown in window title.

Truss wizard
Truss creator

[TEDDS-3583]1 - Added variables for defining the member names, MemberNameTop, MemberNameBottom, MemberNameBottomLeft, MemberNameBottomRight, MemberNameLeft, MemberNameRight.
Fixed Initializer items being run twice when material and design code are not defined.
Modified creator so that input variables are not deleted when finished.

USA

Product bulletin July 2019 (PBT-1907-1)

[TEDDS-3595]1 Wood beam analysis & design (NDS) - Fixed a potentially un-conservative error affecting the calculation of wet service modification factors for compression and compression perpendicular to the grain for both Southern Pine and Mixed Southern Pine. For more detailed information please refer to “Product bulletin July 2019 (PBT-1907-1)” in the Bulletins group of the Engineering Library Index.

Updates

RC beam analysis & design (ACI318)
RC beam design (ACI318)

Refactoring code for integration with other calculations.
[TEDDS-1017]1 - fixed the use of an incorrect lever arm when previous load has been removed in the design only calculation.
[TEDDS-3034]1 - Fixed an error where the flanged details were not taken from the geometry section.
[TEDDS-3163/3164]1 - Fixed an error where spacing checks were included when user defined reinforcement areas were selected.

Steel sheet piling design

[TEDDS-3608]1 Fixed a unit conversion error which gave greater than expected moments in the pile when working in US units.

Truss wizard
Truss creator

[TEDDS-3583]1 - Added variables for defining the member names, MemberNameTop, MemberNameBottom, MemberNameBottomLeft, MemberNameBottomRight, MemberNameLeft, MemberNameRight.
Fixed Initializer items being run twice when material and design code are not defined.
Modified creator so that input variables are not deleted when finished.

Wind loading (ASCE7)

[TEDDS-3201]1 Fixed the value of kz for ASCE7-16 when the height above ground level is less than 30ft and the design method was C and C or directional.

[TEDDS-3242]1 Fixed the missing minimum design pressure note below pressure tables.

[TEDDS-3410]1 Fixed the autogenerted valued for C and C method when the area was greater than 4a2. Loadcases should be deleted and 'auto' created again to fix in existing document.

[TEDDS-630]1 Fixed output tables corrupting formatting when an existing document is re-calculated by ensuring all tables use the grid style "Table Grid".

Australia

Updates

RC beam analysis & design (AS3600)
RC beam design (AS3600)

Refactoring code for integration with other calculations.
[TEDDS-1017]1 - Fixed the use of an incorrect lever arm when previous load has been removed in the design only calculation.
[TEDDS-1019]1 - Fixed a dimensional inequality error with spans in complete hogging.
[TEDDS-3163/3164]1 - Fixed an error where spacing checks were included when user defined reinforcement areas were selected.

Truss wizard
Truss creator

[TEDDS-3583]1 - Added variables for defining the member names, MemberNameTop, MemberNameBottom, MemberNameBottomLeft, MemberNameBottomRight, MemberNameLeft, MemberNameRight.
Fixed Initializer items being run twice when material and design code are not defined.
Modified creator so that input variables are not deleted when finished.

Canada

Updates

Truss wizard
Truss creator

[TEDDS-3583]1 - Added variables for defining the member names, MemberNameTop, MemberNameBottom, MemberNameBottomLeft, MemberNameBottomRight, MemberNameLeft, MemberNameRight.
Fixed Initializer items being run twice when material and design code are not defined.
Modified creator so that input variables are not deleted when finished.

Europe

Updates

Column base plate design (EN1993)

[TEDDS-3210]1 Added to output derivation of Ft,Rd

RC beam analysis & design (EN1992)
RC beam design (EN1992)

Refactoring code for integration with other calculations.
[TEDDS-1017]1 - fixed the use of an incorrect lever arm when previous load has been removed in the design only calculation.
[TEDDS-1648]1 - Enhanced the calculation to include the option to select a user defined concrete strut angle in the shear checks.
[TEDDS-2514]1 - Fixed an error where preview results were sometimes incorrect.
[TEDDS-3034]1 - Fixed an error where the flanged details were not taken from the geometry section.
[TEDDS-3163/3164]1 - Fixed an error where spacing checks were included when user defined reinforcement areas were selected.
[TEDDS-3522]1 - Fixed an error in the preview results with certain end cantilever configurations.

RC pile cap design (EN1992/EN1997)

[TEDDS-3632]1 Fixed undefined variable error 'x_{p1}' when re-calculating a document where the pile locations have been manually modified.
[TEDDS-3637]1 Corrected non standard user interface title.

RC stair design (EN1992)

[TEDDS-3636]1 Fixed version number not been displayed in the user interface title.

Steel member fire resistance design (EN1993)

[TEDDS-3635]1 Fixed calculation version not being displayed in the user interface title.

Timber frame racking panel design (EN1995)

[TEDDS-3638]1 - Amended user interface to ensure calculation version is shown in window title.

Truss wizard
Truss creator

[TEDDS-3583]1 - Added variables for defining the member names, MemberNameTop, MemberNameBottom, MemberNameBottomLeft, MemberNameBottomRight, MemberNameLeft, MemberNameRight.
Fixed Initializer items being run twice when material and design code are not defined.
Modified creator so that input variables are not deleted when finished.

Footnotes

1 This number is an internal reference number and can be quoted to your local Support Department should further information on an item be required.

Content rating: 
No votes yet