Hello!

Did you know that logged in users can see a lot more content?

Tekla Tedds Engineering Library (September 2019)

Last updated September 11, 2019 by Tedds Development Team tekla-product-development-tedds-team-ug@trimble.com

Tekla Tedds Engineering Library (September 2019)

Important

Service Pack 3 is required to use the Tedds Engineering Library (September 2019) or later.


UK and Asia

Steel member analysis & design (EN1993)

Enhanced user experience to simplify the design of single beams or columns, with improved calculation performance and optimisations which allow designs to be completed more quickly than previously.

Batch design

Enhanced to include numerous benefits including:

  • New output option to send the output to the Tedds Application, a project will be created and each design will be added as a project document. If the Output folder is defined then the project file and all the documents will also be automatically saved in the specified folder.
  • New "Batch mode" option "Design first row then modify". Using this mode the first design is run with the normal user interface and then subsequent designs are run using the final results from the first design with any defined inputs applied as modifications to that original design.
  • New "Update input" option which when enabled will save the input variables back to the input sheet when the design case has completed and can therefore be used to record new designs that start with no input or partial input for the design.
  • Enhanced so that when the "Output document" option is "None" the variable "output_detail" is set to "None" which can significantly reduce the time taken for some calculations to calculate because the output will not be processed at all.
  • Enhanced so that if a calculation is cancelled the batch process will stop.
  • Enhanced so that if an incorrect unit is defined for an output variable an appropriate error message will be reported.
  • Fixed calculation error messages not always appearing in the foreground.

Bearing pressures for rectangular footings

Enhanced for improved performance when used via automation or batch design. Output options have also been added to allow the calculation title to be modified, to set the output detail, to optionally include the sketch and user defined notes can also be included.

Other updates

Calculation writing documentation

Documented functions SolvSetMemberRotation and SolvSetElementRotation which were added in Service Pack 2

RC pile cap design (EN1992/EN1997)

[TEDDS-3633]1 Amended pile punching perimeter being considered when not required.
[TEDDS-3687]1 Updated calculation notes to include missing reference to Malaysia national annex.

Timber member analysis & design (EN1995)
Timber 2D analysis & design (EN1995)

[TEDDS-3599]1 - Fixed undefined variable error associated with the sketches of notches at bearings.
General amendments aimed at improving the calculation performance including.
minor amendments to the layout of interface.

USA

Steel member analysis & design (AISC360)

Enhanced user experience to simplify the design of single beams or columns, with improved calculation performance and optimisations which allow designs to be completed more quickly than previously.

Batch design

Enhanced to include numerous benefits including:

  • New output option to send the output to the Tedds Application, a project will be created and each design will be added as a project document. If the Output folder is defined then the project file and all the documents will also be automatically saved in the specified folder.
  • New "Batch mode" option "Design first row then modify". Using this mode the first design is run with the normal user interface and then subsequent designs are run using the final results from the first design with any defined inputs applied as modifications to that original design.
  • New "Update input" option which when enabled will save the input variables back to the input sheet when the design case has completed and can therefore be used to record new designs that start with no input or partial input for the design.
  • Enhanced so that when the "Output document" option is "None" the variable "output_detail" is set to "None" which can significantly reduce the time taken for some calculations to calculate because the output will not be processed at all.
  • Enhanced so that if a calculation is cancelled the batch process will stop.
  • Enhanced so that if an incorrect unit is defined for an output variable an appropriate error message will be reported.
  • Fixed calculation error messages not always appearing in the foreground.

Bearing pressures for rectangular footings

Enhanced for improved performance when used via automation or batch design. Output options have also been added to allow the calculation title to be modified, to set the output detail, to optionally include the sketch and user defined notes can also be included.

Product bulletin September 2019 (PBT-1908-1)

Wood member design (NDS)- Fixed a potentially un-conservative error affecting the design of timber members which are 5" x 5" and larger. For more detailed information please refer to “Product bulletin September 2019 (PBT-1908-1)” in the Bulletins group of the Engineering Library Index.

Other updates

Calculation writing documentation

Documented functions SolvSetMemberRotation and SolvSetElementRotation which were added in Service Pack 2

Australia

Steel member analysis & design (AS4100)

Enhanced user experience to simplify the design of single beams or columns, with improved calculation performance and optimisations which allow designs to be completed more quickly than previously.

Batch design

Enhanced to include numerous benefits including:

  • New output option to send the output to the Tedds Application, a project will be created and each design will be added as a project document. If the Output folder is defined then the project file and all the documents will also be automatically saved in the specified folder.
  • New "Batch mode" option "Design first row then modify". Using this mode the first design is run with the normal user interface and then subsequent designs are run using the final results from the first design with any defined inputs applied as modifications to that original design.
  • New "Update input" option which when enabled will save the input variables back to the input sheet when the design case has completed and can therefore be used to record new designs that start with no input or partial input for the design.
  • Enhanced so that when the "Output document" option is "None" the variable "output_detail" is set to "None" which can significantly reduce the time taken for some calculations to calculate because the output will not be processed at all.
  • Enhanced so that if a calculation is cancelled the batch process will stop.
  • Enhanced so that if an incorrect unit is defined for an output variable an appropriate error message will be reported.
  • Fixed calculation error messages not always appearing in the foreground.

Bearing pressures for rectangular footings

Enhanced for improved performance when used via automation or batch design. Output options have also been added to allow the calculation title to be modified, to set the output detail, to optionally include the sketch and user defined notes can also be included.

Other updates

Calculation writing documentation

Documented functions SolvSetMemberRotation and SolvSetElementRotation which were added in Service Pack 2

Canada

Batch design

Enhanced to include numerous benefits including:

  • New output option to send the output to the Tedds Application, a project will be created and each design will be added as a project document. If the Output folder is defined then the project file and all the documents will also be automatically saved in the specified folder.
  • New "Batch mode" option "Design first row then modify". Using this mode the first design is run with the normal user interface and then subsequent designs are run using the final results from the first design with any defined inputs applied as modifications to that original design.
  • New "Update input" option which when enabled will save the input variables back to the input sheet when the design case has completed and can therefore be used to record new designs that start with no input or partial input for the design.
  • Enhanced so that when the "Output document" option is "None" the variable "output_detail" is set to "None" which can significantly reduce the time taken for some calculations to calculate because the output will not be processed at all.
  • Enhanced so that if a calculation is cancelled the batch process will stop.
  • Enhanced so that if an incorrect unit is defined for an output variable an appropriate error message will be reported.
  • Fixed calculation error messages not always appearing in the foreground.

Bearing pressures for rectangular footings

Enhanced for improved performance when used via automation or batch design. Output options have also been added to allow the calculation title to be modified, to set the output detail, to optionally include the sketch and user defined notes can also be included.

Other updates

Calculation writing documentation

Documented functions SolvSetMemberRotation and SolvSetElementRotation which were added in Service Pack 2

Europe

Steel member analysis & design (EN1993)

Enhanced user experience to simplify the design of single beams or columns, with improved calculation performance and optimisations which allow designs to be completed more quickly than previously.

Batch design

Enhanced to include numerous benefits including:

  • New output option to send the output to the Tedds Application, a project will be created and each design will be added as a project document. If the Output folder is defined then the project file and all the documents will also be automatically saved in the specified folder.
  • New "Batch mode" option "Design first row then modify". Using this mode the first design is run with the normal user interface and then subsequent designs are run using the final results from the first design with any defined inputs applied as modifications to that original design.
  • New "Update input" option which when enabled will save the input variables back to the input sheet when the design case has completed and can therefore be used to record new designs that start with no input or partial input for the design.
  • Enhanced so that when the "Output document" option is "None" the variable "output_detail" is set to "None" which can significantly reduce the time taken for some calculations to calculate because the output will not be processed at all.
  • Enhanced so that if a calculation is cancelled the batch process will stop.
  • Enhanced so that if an incorrect unit is defined for an output variable an appropriate error message will be reported.
  • Fixed calculation error messages not always appearing in the foreground.

Bearing pressures for rectangular footings

Enhanced for improved performance when used via automation or batch design. Output options have also been added to allow the calculation title to be modified, to set the output detail, to optionally include the sketch and user defined notes can also be included.

Other updates

Calculation writing documentation

Documented functions SolvSetMemberRotation and SolvSetElementRotation which were added in Service Pack 2

RC pile cap design (EN1992/EN1997)

[TEDDS-3633]1 Amended pile punching perimeter being considered when not required.
[TEDDS-3687]1 Updated calculation notes to include missing reference to Malaysia national annex.

Timber member analysis & design (EN1995)
Timber 2D analysis & design (EN1995)

[TEDDS-3599]1 - Fixed undefined variable error associated with the sketches of notches at bearings.
General amendments aimed at improving the calculation performance including.
minor amendments to the layout of interface.

Footnotes

1 This number is an internal reference number and can be quoted to your local Support Department should further information on an item be required.

Content rating: 
No votes yet